5–10 giorni
Pagamenti
Descrizione
Descrizione
PolyMide™ CoPA: Copolymer di nylon ad alte prestazioni
Formulazione avanzata di copolymer
PolyMide™ CoPA è costituito da un copolymer blend di nylon 6 e nylon 6,6, progettato per fornire un equilibrio superiore di proprietà meccaniche per applicazioni impegnative.
Strenghezza e rigidità eccezionali
Questo filamento combina eccezionale resistenza e resistenza, rendendolo ideale per le parti funzionali che richiedono durata e resistenza all'impatto.
Alta resistenza al calore
PolyMide™ CoPA sopporta temperature fino a 180 ̊C, fornendo un'eccellente stabilità termica per componenti esposti a calore o ambienti difficili.
Ideale per Engineering e parti industriali
Scegli PolyMide™ CoPA quando il tuo progetto richiede alta resistenza, resistenza e resistenza al calore - perfetto per applicazioni automobilistiche, meccaniche e industriali.
Requisiti di stampa
Imprinta impostazioni
Imprinta impostazioni
PolyMide™ CoPA
Caratteristiche chiave
- Copolymer di nylon 6/6,6
- Alta forza e rigidità
- Resistente al calore
- Ideale per le parti Engineering
PolyMide™ CoPA - Nero / 1.75mm / 0.75kg ...è stato ordinato al fornitore e verrà spedito non appena sarà di nuovo disponibile.
Specificità tecniche
Tutto quello di cui hai bisogno prima di stampare
Suggerimenti per la stampa
- Tenere il filamento sigillato e asciutto; utilizzare il ciclo di asciugatura elencato 100°C / 8h se si verificano difetti legati all'umidità.
- Utilizzare un recinto, evitare i disegni e mantenere la temperatura consigliata per ridurre la deformazione e la separazione di strati.
- Utilizzare un adesivo adatto come strato di rilascio e lasciare raffreddare la piastra di costruzione prima di rimuovere la parte.
- Utilizzare una scatola completamente in metallo hotend e stampare da una scatola secca perché questo materiale engineering richiede elevate temperature e rigoroso controllo dell'umidità.
- Iniziare all'interno dei ranghi di letto raccomandati 250 - 270°C e 25 - 50°C, quindi effettuare piccole regolazioni per la stampante e il modello.
- Utilizzare l'impostazione di ventilatore di raffreddamento OFF raccomandata e mantenere la velocità di stampa entro 50 - 200 mm/s.
- Se PolyMide™ CoPA viene utilizzato come materiale di supporto per se stesso, si prega di rimuovere la struttura di supporto prima di assorbire eccessivamente l'umidità. In caso contrario, la struttura di supporto può essere legata al modello in modo permanente.
| Proprietà | X-Y | Z | Valore | Metodo |
|---|---|---|---|---|
| Densità | — | — | 1.12 g/cm³ Importanti | ISO 1183 |
| Resistenza della tensione | 78 MPa Importanti | 45.8 MPa Importanti | — | ISO 527 |
| allungamento al momento della pausa | 12.7 % Importanti | 1.3 % Importanti | — | ISO 527 |
| Forza di piegatura | 109.8 MPa Importanti | — | — | ISO 178 |
| Modulo di piegatura | 2510 GPa Importanti | — | — | ISO 178 |
| Modulo di Young | 2703 GPa Importanti | 2209 GPa Importanti | — | ISO 527 |
| Carpi, incisivi | 27.7 KJ/m² Importanti | — | — | ISO 179 |
| Temperatura di fusione | — | — | 189 °C Importanti | ISO 11357 |
| Temperatura di transizione del vetro (Tg) | — | — | 66 °C Importanti | ISO 11357 |
| Temperatura di ammorbidimento | — | — | 180 °C Importanti | ISO 306 |
| HDT (0.45 MPa) | — | — | 111 °C Importanti | ISO 75 |
| HDT (1.8 MPa) | — | — | 70 °C Importanti | ISO 75 |
Testato su esemplari 100% infill. X-Y = attraverso gli strati, Z = tra gli strati (adesione dello strato).
Domande frequenti
Ha delle domande? Abbiamo risposte. Dalla scelta del materiale giusto alla cura delle cuciture, ecco tutto quello che devi sapere in un unico posto.
PolyMide™ CoPA richiede una stampante chiusa?
Posso usare PolySupport™ for PA12 con CoPA?
Hai bisogno di annellare PolyMide™ CoPA?
Che cos’è la ricottura?
Cos'è il condizionamento dell'umidità?
Devo inilare prima o dopo il condizionamento dell'umidità?
Perche' usi una temperatura di piastra così bassa con le tue nylon?
Le bobine funzionano con AMS?
Qual è il tasso di contrazione di PolyMide™ CoPA?
Recensioni
Customers praised this nylon filament for producing "extremely strong" and durable parts with minimal warping. Many noted it "prints like a dream" with proper drying and temperature settings. The material excels for functional parts, gears, and automotive applications with heat resistance to 180-220°F. Some found print profile calibration challenging initially. Shoppers recommend using a dryer and hardened nozzle.
I can't tear it by hand, and I'm a big boy.
Great quality filament and packaging as always! Default print profiles were well tuned.
Printed a part for my gearbox and this CoPA is perfect for that.
Printed very nicely
This prints really well and has a very nice finish. It didn't warp hardly at all during printing or annealing. I annealed it on my removable build plate with supports attached. Seems like heat resistance to about 220F.
Ender 3 all metal hotend. 272c /50c 25mms .6 nozzle. glass bed. You must dry and print from a dryer 70c. dried in oven at 90c for hour then over night at 70c. copper nozzle that is plated.
This stuff is nothing short of amazing with the right setup and prints well open frame whereas ASA prints without a popup are super brittle (for me).Printing this in my garage which is around 40-50 degrees Fahrenheit with the Eibos Cyclopes dryer at 70 degrees and a reverse Bowden from the dry box to my direct drive setup.Ender 5 Pro with a microswiss hotend, BMG clone extruder and microswiss 0.6 hardened steel nozzle at 280C 60mm/s. Fan at 0 except for bridging/overhangs and support interface. PEI sheet on the flat side with a little glue stick 90C first layer 35C other layers the parts stick so solidly you can pick the entire printer up by grabbing the part and it won't let go so definitely not warping!Video attached shows me beating a bracket printed with a mini sledge, no other filament I've used would come close to taking that abuse and even after breaking the split section was still holding on enough that you couldn't pull it apart without twisting it.
Had to dig around to find the right profile for my Bambu printer, but once I did it printer perfectly. Tough stuff!
The filament itself worked great, but I had issues with the print profiles, and I had to calibrate the settings manually.
This filament works great in my bambu p1s and AMS
After some drying (which should absolutely be expected) I got incredible prints with this filament. It covers up layer lines very well, especially if you use fuzzy skin. Do not buy if you don't have a dryer, unless you can dry it before printing, and you're only doing a short print, as this filament definitely holds moisture.
Can be used to make under the hood car parts and intakes. Prints like a dream asking as the your printer is enclosed.
this nylon works great, i had to print a large flange of 22" in dia on an open printer and this printed great, no curling, no delamination and also the part came out super tough after some days of acclimating.highly recommend
This plus 0.4 Obxidian hot end, 275C with X1C presets for their version of the material... Prints are looking very nice. Only complaint is that I wish the spools were 1kg.
Fast delivery, good service
works great and looks amazing, strongly suggest making sure the filament does not have any tight corners as it is brittle at filament and beastly strong printed
Took little to no tweaking to get this to print correctly. Had great layer and bed adhesion from what I've experienced with other carbon fiber nylons. I've been able to print multiple functional parts with this stuff first attempt.I recommend this and would absolutely buy it again.
This is a good filament. Very durable, and water isn't too much of concern with it like with other nylons. Just wish it wasn't so expensive.
Printing with a stock ender 5 pro with micro swiss hot end at 260 this stuff works great. even unenclosed. very tough. use painters tape and glue sticks for adhesion on stock ender print bed.
Exactly as the title says, its completely warp-free and extremely strong when printed slower. my print settings are 250c hotend, 50c bed, 5mm^3/s volumetric speed, and I use Magigoo PA for guaranteed success (not required)
The filament is hard to print no doubt but if you keep it dry and do the right settings and have the right adhesion it will print. Warping is normal
I used this for printing some 3d printer parts for a vzbot and worked great bo encloser needed and bed temp doesn't have to be as hot as boiling water just need a high temp hotend and abrasive resistant nozzle
First part delaminated miserably due to poor interlayer adhesion - This was fixed by upping the printhead temperature. We use diamondback nozzles that have extremely good heat transfer capabilities so we normally have to reduce temps by at least 15 degrees C, but this filament needed more heat and worked fine after adjusting temp higher.
Prints really well. Printed car parts and candle holders. Beautiful finish.
It was very easy to print. It does require a hardened or ruby nozzle. Bed adhesion was great with a glue stick, and it produces incredibly strong parts.
TLDR Was more impressed by this material after I broke my printer. Be sure you have proper hotend/nozzles, maybe even a spare.I only ran a few prints through a standard head and nozzle just to get a small test piece of material. Was planning on replace my hot side so I ran a print that would likely fail because of my subpar equipment. Hotend did fail but the chunk of material i removed with my broken hotside was impressive. Couldnt be broken by hand or with standard hand plyers.Cant wait to make more with this material when I have proper hotend and nozzle. Definitely a good choice for replacing nylon bushings in non-heated automotive applications. I was printing a variety of different bushings for my work truck before hotend failure. ie: tailgate hinge bushing, cornerlight catch pin, and would have liked to try a small gas cap for a mower.
It's pretty much all I use. The best price I've found for such a good quality carbon fiber nylon. I plan on being a long-term customer.
After I was able to get the temp right and speed right it worked good. It looks good and the printed parts are really tough
i've used most major carbon fiber infused nylons. this is hands down the best, significantly stronger than either carbonX or NylonX, the print finish looks flawless like NylonX and prints as easy as carbonX with no vibisble warp. Also far less hydroscopic than both as its Nylon-12. Without drying I had better prints than both on first attempt. printed at 110 on the bed and 285 on the hotend
Copa took a bit to dial it in but wow this is strong stuff and prints smooth.. But doesn't like overhangs much.. Could be in my settings tho.. As most know every printer is different with settings..I turned up my feed rate to 115% and made a huge difference in layer adhesion and Wall adhesion. Using the creality spider hot end and simplify 3d slicer.. And printing at 240 temp.. .24 up to .32 layer thickness
