5-10 days
Payments
Descripción
Descripción
PolyMide™ CoPA: Copolímero de nailon de alto rendimiento
Formulación avanzada de copolímero
PolyMide™ CoPA está fabricado a partir de una mezcla de copolímeros de nailon 6 y nailon 6,6, diseñada para ofrecer un equilibrio superior de propiedades mecánicas en aplicaciones exigentes.
Resistencia y tenacidad excepcionales
Este filamento combina una resistencia y una tenacidad sobresalientes, por lo que es ideal para piezas funcionales que requieren durabilidad y resistencia a los impactos.
Alta resistencia térmica
PolyMide™ CoPA soporta temperaturas de hasta 180˚C, proporcionando una excelente estabilidad térmica para componentes expuestos al calor o a entornos exigentes.
Ideal para piezas técnicas e industriales
Elige PolyMide™ CoPA cuando tu proyecto requiera alta resistencia, tenacidad y resistencia térmica: es perfecto para aplicaciones automotrices, mecánicas e industriales.
Requisitos de impresión
Ajustes de impresión
Ajustes de impresión
PolyMide™ CoPA
- Nylon 6/6,6 Copolymer
- High Strength & Toughness
- Heat Resistant
- Ideal for Engineering Parts
PolyMide™ CoPA - 1.75mm / 0.75kg / Negro está en pedido pendiente y se enviará tan pronto como vuelva a estar en stock.
Especificaciones técnicas
Todo lo que necesitas antes de imprimir
- Mantén el filamento sellado y seco; utiliza el ciclo de secado indicado de 100 °C / 8 h si aparecen defectos relacionados con la humedad.
- Utiliza una cámara cerrada, evita las corrientes de aire y mantén la temperatura recomendada de la plataforma para reducir la deformación y la separación de capas.
- Utiliza un adhesivo adecuado como capa de separación y deja que la plataforma de impresión se enfríe antes de retirar la pieza.
- Utiliza un hotend totalmente metálico e imprime desde una caja seca, ya que este material de ingeniería requiere una temperatura alta y un control estricto de la humedad.
- Comienza dentro de los intervalos recomendados de 250 - 270 °C para la boquilla y de 25 - 50 °C para la plataforma; después, realiza pequeños ajustes según la impresora y el modelo.
- Utiliza el ajuste recomendado de ventilador de refrigeración APAGADO y mantén la velocidad de impresión entre 50 - 200 mm/s.
- Si PolyMide™ CoPA se utiliza como material de soporte para sí mismo, retira la estructura de soporte antes de que absorba demasiada humedad. De lo contrario, la estructura de soporte puede quedar unida permanentemente al modelo.
| Property | X-Y | Z | Value | Method |
|---|---|---|---|---|
| Density | — | — | 1.12 g/cm³ Important | ISO 1183 |
| Tensile strength | 78 MPa Important | 45.8 MPa Important | — | ISO 527 |
| Elongation at break | 12.7 % Important | 1.3 % Important | — | ISO 527 |
| Bending strength | 109.8 MPa Important | — | — | ISO 178 |
| Bending modulus | 2510 MPa Important | — | — | ISO 178 |
| Young's modulus | 2703 MPa Important | 2209 MPa Important | — | ISO 527 |
| Charpy, notched | 27.7 KJ/m² Important | — | — | ISO 179 |
| Melting temperature | — | — | 189 °C Important | ISO 11357 |
| Glass transition temperature (Tg) | — | — | 66 °C Important | ISO 11357 |
| Vicat softening temperature | — | — | 180 °C Important | ISO 306 |
| HDT (0.45 MPa) | — | — | 111 °C Important | ISO 75 |
| HDT (1.8 MPa) | — | — | 70 °C Important | ISO 75 |
Probado en muestras con un 100 % de relleno. X-Y = transversal a las capas, Z = entre las capas (adhesión entre capas).
Preguntas frecuentes
¿Tienes preguntas? Tenemos las respuestas. Desde elegir el material adecuado hasta cuidar tus bobinas, aquí encontrarás todo lo que necesitas saber en un solo lugar.
Does PolyMide™ CoPA requires an enclosed printer?
Can I use PolySupport™ for PA12 with CoPA?
Do you need to anneal PolyMide™ CoPA?
What is annealing?
What is moisture conditioning?
Should I anneal before or after moisture conditioning?
Why do you use such a low build plate temperature with your nylons?
Will the spools work in an AMS?
What is the shrinkage rate of PolyMide™ CoPA?
Customers praised this nylon filament as "extremely strong" and "prints like a dream" with minimal warping. Many noted it requires proper drying and higher temperatures (260-280°C) for best results. Some experienced initial calibration challenges with print profiles. "Incredibly strong parts" are achievable with correct settings and a hardened nozzle.
Great quality filament and packaging as always! Default print profiles were well tuned.
Printed a part for my gearbox and this CoPA is perfect for that.
Printed very nicely
This prints really well and has a very nice finish. It didn't warp hardly at all during printing or annealing. I annealed it on my removable build plate with supports attached. Seems like heat resistance to about 220F.
Ender 3 all metal hotend. 272c /50c 25mms .6 nozzle. glass bed. You must dry and print from a dryer 70c. dried in oven at 90c for hour then over night at 70c. copper nozzle that is plated.
This stuff is nothing short of amazing with the right setup and prints well open frame whereas ASA prints without a popup are super brittle (for me).Printing this in my garage which is around 40-50 degrees Fahrenheit with the Eibos Cyclopes dryer at 70 degrees and a reverse Bowden from the dry box to my direct drive setup.Ender 5 Pro with a microswiss hotend, BMG clone extruder and microswiss 0.6 hardened steel nozzle at 280C 60mm/s. Fan at 0 except for bridging/overhangs and support interface. PEI sheet on the flat side with a little glue stick 90C first layer 35C other layers the parts stick so solidly you can pick the entire printer up by grabbing the part and it won't let go so definitely not warping!Video attached shows me beating a bracket printed with a mini sledge, no other filament I've used would come close to taking that abuse and even after breaking the split section was still holding on enough that you couldn't pull it apart without twisting it.
The filament itself worked great, but I had issues with the print profiles, and I had to calibrate the settings manually.
This filament works great in my bambu p1s and AMS
After some drying (which should absolutely be expected) I got incredible prints with this filament. It covers up layer lines very well, especially if you use fuzzy skin. Do not buy if you don't have a dryer, unless you can dry it before printing, and you're only doing a short print, as this filament definitely holds moisture.
Can be used to make under the hood car parts and intakes. Prints like a dream asking as the your printer is enclosed.
this nylon works great, i had to print a large flange of 22" in dia on an open printer and this printed great, no curling, no delamination and also the part came out super tough after some days of acclimating.highly recommend
This plus 0.4 Obxidian hot end, 275C with X1C presets for their version of the material... Prints are looking very nice. Only complaint is that I wish the spools were 1kg.
Fast delivery, good service
works great and looks amazing, strongly suggest making sure the filament does not have any tight corners as it is brittle at filament and beastly strong printed
Took little to no tweaking to get this to print correctly. Had great layer and bed adhesion from what I've experienced with other carbon fiber nylons. I've been able to print multiple functional parts with this stuff first attempt.I recommend this and would absolutely buy it again.
This is a good filament. Very durable, and water isn't too much of concern with it like with other nylons. Just wish it wasn't so expensive.
Printing with a stock ender 5 pro with micro swiss hot end at 260 this stuff works great. even unenclosed. very tough. use painters tape and glue sticks for adhesion on stock ender print bed.
I run this on my Ender 3 V2 with a Micro Swiss all-Metal Hot end and direct drive extruder with Marlin firmware. 275DegC at 50mm/s is perfect, prints better than Pro PLA+ (for me, YMMV) This is my new go-to filament, and the fact that Polymaker is 2A friendly is even better.
Exactly as the title says, its completely warp-free and extremely strong when printed slower. my print settings are 250c hotend, 50c bed, 5mm^3/s volumetric speed, and I use Magigoo PA for guaranteed success (not required)
The filament is hard to print no doubt but if you keep it dry and do the right settings and have the right adhesion it will print. Warping is normal
I used this for printing some 3d printer parts for a vzbot and worked great bo encloser needed and bed temp doesn't have to be as hot as boiling water just need a high temp hotend and abrasive resistant nozzle
First part delaminated miserably due to poor interlayer adhesion - This was fixed by upping the printhead temperature. We use diamondback nozzles that have extremely good heat transfer capabilities so we normally have to reduce temps by at least 15 degrees C, but this filament needed more heat and worked fine after adjusting temp higher.
Prints really well. Printed car parts and candle holders. Beautiful finish.
It was very easy to print. It does require a hardened or ruby nozzle. Bed adhesion was great with a glue stick, and it produces incredibly strong parts.
TLDR Was more impressed by this material after I broke my printer. Be sure you have proper hotend/nozzles, maybe even a spare.I only ran a few prints through a standard head and nozzle just to get a small test piece of material. Was planning on replace my hot side so I ran a print that would likely fail because of my subpar equipment. Hotend did fail but the chunk of material i removed with my broken hotside was impressive. Couldnt be broken by hand or with standard hand plyers.Cant wait to make more with this material when I have proper hotend and nozzle. Definitely a good choice for replacing nylon bushings in non-heated automotive applications. I was printing a variety of different bushings for my work truck before hotend failure. ie: tailgate hinge bushing, cornerlight catch pin, and would have liked to try a small gas cap for a mower.
It's pretty much all I use. The best price I've found for such a good quality carbon fiber nylon. I plan on being a long-term customer.
After I was able to get the temp right and speed right it worked good. It looks good and the printed parts are really tough
i've used most major carbon fiber infused nylons. this is hands down the best, significantly stronger than either carbonX or NylonX, the print finish looks flawless like NylonX and prints as easy as carbonX with no vibisble warp. Also far less hydroscopic than both as its Nylon-12. Without drying I had better prints than both on first attempt. printed at 110 on the bed and 285 on the hotend
Copa took a bit to dial it in but wow this is strong stuff and prints smooth.. But doesn't like overhangs much.. Could be in my settings tho.. As most know every printer is different with settings..I turned up my feed rate to 115% and made a huge difference in layer adhesion and Wall adhesion. Using the creality spider hot end and simplify 3d slicer.. And printing at 240 temp.. .24 up to .32 layer thickness
I have used this filament for many applications, and it is effortless to print with. I noticed it does absorb moisture rather quickly, causing crackling as the filament is extruded through the printer head. But I have had no problems with my prints. It is important to follow the recommended setting. It is extremely tough and is heat resistant to 180 c. Good for industrial parts. I have made many gears out of this, and they do not wear down. I would highly recommend this over ABS, but it is about twice the price of ABS. So, pay less and deal with the warping issues or pay more and print strong parts as easily as printing PLA.
